ASTM A394 PDF

More F The following types of bolts are: Type 0 includes hot-dip zinc-coated bolts made of low or medium carbon steel, Type 1 includes hot-dip zinc-coated bolts made of medium carbon steel, quenched and tempered, Type 2, and Type 3 includes bare, quenched, and tempered bolts made of weathering steel. Steel for the manufacture of bolts shall be made by any of the following processes: open-hearth, electric-furnace, or basic-oxygen. Type 1 bolts produced from medium carbon steel shall be quenched in a liquid medium from above the austenizing temperature. Type 1 bolts produced from medium carbon steel to which chromium, nickel, molybdenum, or boron were intentionally added shall be quenched only in oil from above the austenitizing temperature.

Author:Kajigor Kigashakar
Country:Poland
Language:English (Spanish)
Genre:Technology
Published (Last):1 August 2018
Pages:25
PDF File Size:5.32 Mb
ePub File Size:9.97 Mb
ISBN:895-5-66789-130-7
Downloads:86735
Price:Free* [*Free Regsitration Required]
Uploader:Akinozshura



More F The following types of bolts are: Type 0 includes hot-dip zinc-coated bolts made of low or medium carbon steel, Type 1 includes hot-dip zinc-coated bolts made of medium carbon steel, quenched and tempered, Type 2, and Type 3 includes bare, quenched, and tempered bolts made of weathering steel. Steel for the manufacture of bolts shall be made by any of the following processes: open-hearth, electric-furnace, or basic-oxygen.

Type 1 bolts produced from medium carbon steel shall be quenched in a liquid medium from above the austenizing temperature. Type 1 bolts produced from medium carbon steel to which chromium, nickel, molybdenum, or boron were intentionally added shall be quenched only in oil from above the austenitizing temperature. Type 3 bolts shall be quenched only in oil from above the austenitizing temperature. Cold-headed Type 0 bolts shall be stress relief annealed before zinc coating to remove cold work effects such that the hardness measured anywhere on the surface or through the cross-section shall meet the requirement specified.

Different tests shall be conducted in order to determine the following mechanical properties of bolts: hardness, tensile strength, and shear strength. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Scope 1. The various types of bolts covered in this specification are: 1. No other units of measurement are included in this standard. This standard does not purport to address all of the safety concerns, if any, associated with its use.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

EL SALVOCONDUCTO BORIS PASTERNAK PDF

A394 TOWER BOLTS.

We use lock washer helical spring to secure the bolt and nut. I was getting less than 90 ft-lbs to install and the crews were complaining it was tearing their impact guns up. Now any pneumatic impact wrench should be able to put out ft-lbs but I guess tightening bolts per day may have taken their toll over the years. We used to buy bolts and nuts separate in 2 boxes of about 25 pounds. I joke about our crews that they would make up a connection and pour out the box of bolts onto the holes and the ones that went in the hole would get a nut installed and the rest of the bolts were left on the ground so when it god muddy, they would have something to walk on.

CCAG FCS 1977 PDF

ASTM A394 Type 1

The following types of bolts are: Type 0 includes hot-dip zinc-coated bolts made of low or medium carbon steel, Type 1 includes hot-dip zinc-coated bolts made of medium carbon steel, quenched and tempered, Type 2, and Type 3 includes bare, quenched, and tempered bolts made of weathering steel. Steel for the manufacture of bolts shall be made by any of the following processes: open-hearth, electric-furnace, or basic-oxygen. Type 1 bolts produced from medium carbon steel shall be quenched in a liquid medium from above the austenizing temperature. Type 1 bolts produced from medium carbon steel to which chromium, nickel, molybdenum, or boron were intentionally added shall be quenched only in oil from above the austenitizing temperature. Type 3 bolts shall be quenched only in oil from above the austenitizing temperature. Cold-headed Type 0 bolts shall be stress relief annealed before zinc coating to remove cold work effects such that the hardness measured anywhere on the surface or through the cross-section shall meet the requirement specified. Different tests shall be conducted in order to determine the following mechanical properties of bolts: hardness, tensile strength, and shear strength.

LARCENET COMBAT ORDINAIRE PDF

ASTM A394 Specification

.

Related Articles