Metal Building Insulation Metal Building Insulation The Simple Saver System is a high performance insulation and finishing system designed for roof and walls in low rise commercial buildings. The Simple Saver System is a high R-value insulation system for metal buildings that also provides through fall protection when properly installed. Simple Saver System will yield designed insulation values without excessive compression and voids, which are common with other methods of installation. The Simple Saver fabric liner system uses a strong, low permeance vapor retarder to create the required space for designed insulation thickness between the structural members while isolating conductive secondary framing members from the inside conditioned air. Fabricated Products Fabricated Products As part of our product offerings, General Insulation Company provides high-quality fabricated insulation for all mechanical systems. With three dedicated facilities to cut cellular glass, urethane, expanded polystyrene, stone wool, and phenolic insulations, we are capable of fabricating pipe insulation and fittings for any small or large project.

Author:Kisho Tygojinn
Language:English (Spanish)
Published (Last):27 November 2006
PDF File Size:11.22 Mb
ePub File Size:4.88 Mb
Price:Free* [*Free Regsitration Required]

They also do not cause any issues with garage door openers as the panels are tailored to fit with minor trimming. It may come to a surprise to many but buying insulation for garage doors is relatively cheap and long lasting with very little maintenance required. Paying a small amount extra for a top rated insulation kit is highly recommended.

Below is a list of the best garage door insulation kits that keep the heat in during the winter and keep it out during the summer. The Best Garage Door Insulation 1. The brand claim that you can install it in less than a hour and the savings will pay for itself as you will be using less energy to maintain a comfortable temperature. The two sizes include the standard size kit, which is suitable for a 7 foot tall and 8 to 9 foot wide door.

The larger size is suitable for 8 foot tall and 8 to 9 foot wide garage doors. Check it Out 2. Owens Corning Garage Door Insulation The Owens Corning garage door insulation kit is popular option that uses easy to install pre-cut panels. The brand states their product provides 5 times better thermal performance when compared to an insulated door, which is very impressive. In terms of the installation, Owens Corning claim that it takes approximately 1 hour and all that is required is a tape measure, knife, straight edge and a marker.

The fastening system and flexible insulation make it a quick and simple installation. Check it Out 3. In terms of the installation, it uses a heavy duty double sided tape, which makes it far easier to install when compared to similar alternatives. Check it Out 4. It uses a mixture of fiberglass and polymer materials with a 2 inch thickness to provide superior insulation qualities.

Other features of the Anco Garage Insulation include: Insulation r-value of 9 Suitable for 9 feet wide garage doors Easy to install with no special tools required 2 inch thick construction The Anco garage door insulation kit provides the best thermal performance compared against all the alternatives but you do have to pay a premium for this efficiency.

On top of the thermal performance, the insulation provides excellent noise reduction that makes your garage a more comfortable place to be. Check it Out 5.

Reach Barrier Garage Insulation Reach Barrier is another popular garage door insulation and is the cheapest within this article. Check it Out 6. In terms of the insulation coverage, it measures as 18 feet wide and 7 feet in height, which the brand claims is easy to install.

The unique design creates an air pocket, which maintains the temperature by reducing heat loss in the winter and reducing the heat by 8 degrees in the summer. Check it Out 7. Cellofoam Garage Door Insulation Kit The Cellofoam Kit is designed to provide garage door insulation for standard 9 feet doors and comes with easy to follow instructions.

There are 8 pieces to the kit that measure up as 20 x 15 x 1. In terms of the construction, the garage door insulation panels are made from modified expanded polystyrene and a rigid foamed plastic with resilient closed cells.

Other features of the Cellofoam Insulation Kit include: R-value of 4. Check it Out 8. Check it Out Garage Door Insulation Kit Buying Guide Many people spend a lot of time in their garages, whether that is working on a car to using it as a gym. However, the garage is one place with the least-efficient use of energy since the garage door is made of wood, aluminum or steel. They are usually uninsulated, which during summer or winter, temperature levels in the garage can reach both extremes.

Investing into the best garage door insulation kit helps to prevent this from happening and improves the efficiency of your home. To help you make an informed buying decision, we have produced the below guide regarding DIY garage door insulation kits.

Steps to Install Garage Door Insulation Kits Installing an insulation kit to your garage door is not as hard as you would think. It can be completed by yourself but having another person to help does make things much easier. Below are some steps that you to follow in order to achieve a simple and stress free installation.

Preparing the Surface As you are preparing the inside of the garage door, there is no need to worry about the state of the garage door facing outwards. However, installation of an insulator needs adhesive which requires a clean surface to stick to, thus cleaning of the garage doors is vital. To ensure that the garage door is completely clean, you can use either acetone or a degreaser and later wiping it down with warm water.

Once it dries up, you can then apply the adhesive to the door. Application of the Adhesive Double sided tape is a popular choice for a strong adhesive and most kits comes with multiple Velcro adhesive squares too.

For tab installations, you should follow the instructions on the manual because the application of adhesive tabs is the most time-consuming of the whole process. The next step is removing the protective covers from the tabs and sticking them to the door. You can then follow up by removing the second protective cover from the adhesive part in contact with the barrier. Test Fit Some Panels Before removing the outer protective adhesive casings, test to see if the panels fit.

Carry out a test install before the adhesive sticks to the panels because this enables you to determine which panels need adjustment or trimming to fit perfectly. You should measure the panels, adding several inches before carefully cutting. Subsequently, this is followed up by cutting the panels to leave a few inches at the bottom to wrap into the panel supports of the garage door. Installation of Radiant Barrier Insulation Panels Exposing the top row of adhesives and following that up with installing a panel at the topmost portion enables you to stretch the material before pushing it onto adhesive tabs.

This has the effect of eliminating any wrinkles from showing after installation is complete. Type of Insulation The type of insulation kits available come with different properties, thickness, durability levels, shapes, cost per size, life spans and other factors.

Below are the three most common types of insulation kits on the market. Reflective Foil This insulator is sold on rolls and usually has a thickness of about an inch and a half. Purchasing the reflective foil can either be a single file or double file, depending on your requirements. In between the two aluminum foils is a layer of polyethylene foam, with double foil insulation coming with two coats of this foam. Despite not being aesthetically pleasing, the reflective foil is a very useful insulator especially for regions with hot climates as it is reflecting the radiant heat.

Furthermore, its R-value ranges from 3. Polystyrene Foam Usually sold in large sheets, polystyrene foam needs to be cut to a size equivalent to that of the garage door. This material is very rigid and provides high insulating values despite being of relatively little thickness. Furthermore, the material is more robust to work with in comparison to reflective foil and offers better insulation. Panel Kits For those who value aesthetics, panel kits is the best garage insulation to go for and are easier to install.

They are made of plastic laminated polystyrene or fiberglass and the kit comes with pre-cut panels that comfortably fit into the channels of the garage door frame.

Polystyrene offers better insulation in comparison to fiberglass, but fiberglass is more resistant to mold and water. Installation of both these panels is fairly simple with both taking around an hour to fully install. Factors to Consider when Choosing Insulator Not all garage door insulation kits are the same and many can be fairly expensive.

For that reason, its essential that you understand the basic factors to consider and what to look out for in order to get the best value for your money. Effectiveness of Insulator All garage door insulation are rated using the R-value rating system.

Insulation kits with a higher R-value will provide better insulating properties. Installation Cost Depending upon whether you plan to fit the garage door insulation yourself or not, you may have to budget in the installation. If this is the case, you may want to look into upgrading the opener before adding additional weight to the door. However, most openers can handle a slight increase in weight.

Research your Garage Door Not all garage doors are the same and you may not require that much garage door insulation. However, if the door has no insulation or padding whatsoever, you will want a complete kit that can be installed fairly easily. Conclusion Insulation for your garage door should be an essential component.

It keeps the heat inside the garage during the cold winter months and the heat out during the summer. This instantly boosts the efficiency and pays for itself when you factor in wasted energy costs. All the recommendations in this article are affordable and suit the majority of garage doors from single to double and even custom sizes. We advise that you take your time with your measurements before choosing a garage door insulation kit.

The last thing you would want are panels that are too small or those that require lots of trimming. We also recommend spraying garage door lubrication within any of the moving parts that will be covered up by the insulation. This saves time removing the insulation in case there are any problems in the future. Written By Dan About the Author Dan is an automotive journalist and owner of over 10 cars ranging from supercars, tuned cars, classics and your good old beater cars.

He always like to get his hands dirty with nut and bolt restorations or detailing sessions using the best products on the market.


Thermax, Inc.



The Best Garage Door Insulation Kit 2020



Dow Thermax Sheathing


Related Articles